android/drivers/misc/mediatek/usb11/musbfsh_virthub.c

/*
 * MUSB OTG driver virtual root hub support
 *
 * Copyright 2005 Mentor Graphics Corporation
 * Copyright (C) 2005-2006 by Texas Instruments
 * Copyright (C) 2006-2007 Nokia Corporation
 *
 * Copyright 2015 Mediatek Inc.
 *	Marvin Lin <marvin.lin@mediatek.com>
 *	Arvin Wang <arvin.wang@mediatek.com>
 *	Vincent Fan <vincent.fan@mediatek.com>
 *	Bryant Lu <bryant.lu@mediatek.com>
 *	Yu-Chang Wang <yu-chang.wang@mediatek.com>
 *	Macpaul Lin <macpaul.lin@mediatek.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.
 *
 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
 * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/time.h>
#include <linux/timer.h>

#include <asm/unaligned.h>

#include "musbfsh_core.h"
#include "musbfsh_host.h"
#include "usb.h"

#ifdef CONFIG_MTK_ICUSB_SUPPORT
#include "musbfsh_mt65xx.h"
#endif


#ifdef CONFIG_MTK_ICUSB_SUPPORT
struct my_attr resistor_control_attr = {
	.attr.name = "resistor_control",
	.attr.mode = 0644,
#ifdef MTK_ICUSB_RESISTOR_CONTROL
	.value = 1
#else
	.value = 0
#endif
};

struct my_attr skip_port_pm_attr = {
	.attr.name = "skip_port_pm",
	.attr.mode = 0644,
#ifdef MTK_ICUSB_SKIP_PORT_PM
	.value = 1
#else
	.value = 0
#endif
};

#endif

static void musbfsh_port_suspend(struct musbfsh *musbfsh, bool do_suspend)
{
	u8 power;
	u8 intrusbe;
	u8 intrusb;
	void __iomem *mbase = musbfsh->mregs;
	int retries = 0;


	/* MYDBG("cpuid:%d\n", smp_processor_id()); */

	/* NOTE:  this doesn't necessarily put PHY into low power mode,
	 * turning off its clock; that's a function of PHY integration and
	 * MUSBFSH_POWER_ENSUSPEND.  PHY may need a clock (sigh) to detect
	 * SE0 changing to connect (J) or wakeup (K) states.
	 */
	if (do_suspend) {

#ifdef CONFIG_MTK_DT_USB_SUPPORT
		if (musbfsh_skip_port_suspend) {
			MYDBG("\n");
			musbfsh->port1_status |= USB_PORT_STAT_SUSPEND;
			return;
		}
#endif

		/* clean MUSBFSH_INTR_SOF in MUSBFSH_INTRUSBE */
		intrusbe = musbfsh_readb(mbase, MUSBFSH_INTRUSBE);
		intrusbe &= ~MUSBFSH_INTR_SOF;
		musbfsh_writeb(mbase, MUSBFSH_INTRUSBE, intrusbe);
		mb(); /* flush POWER and PHY setting immediately */
		/* clean MUSBFSH_INTR_SOF in MUSBFSH_INTRUSB */
		intrusb = musbfsh_readb(mbase, MUSBFSH_INTRUSB);
		intrusb |= MUSBFSH_INTR_SOF;
		musbfsh_writeb(mbase, MUSBFSH_INTRUSB, intrusb);
		mb(); /* flush POWER and PHY setting immediately */
		retries = 10000;
		intrusb = musbfsh_readb(mbase, MUSBFSH_INTRUSB);
		while (!(intrusb & MUSBFSH_INTR_SOF)) {
			intrusb = musbfsh_readb(mbase, MUSBFSH_INTRUSB);
			if (retries-- < 1) {
				MYDBG("\n");
				break;
			}
		}

		/* delay 10 us */
		udelay(10);

		/* set MUSBFSH_POWER_SUSPENDM in MUSBFSH_POWER_SUSPENDM */
		power = musbfsh_readb(mbase, MUSBFSH_POWER);
#ifdef CONFIG_MTK_DT_USB_SUPPORT
#if defined(CONFIG_PM_RUNTIME) &&  defined(USB11_REMOTE_IRQ_NON_AUTO_MASK)
		disable_remote_wake_up();
#endif
#endif

#ifdef MTK_USB_RUNTIME_SUPPORT
		/*
		 * mask remote wake up IRQ between port suspend and bus suspend.
		 * hub.c will call set_port_feature first then
		 * usb_set_device_state, so if EINT comes between them,
		 * resume flow may see device state without USB_STATE_SUSPENDED
		 * and do nothing.
		 * So we postpone remote wake up IRQ until the suspend flow
		 * is all done (when bus_suspend is called). Since suspend flow
		 * may be interrupted (root hub is suspended, but not host
		 * controller), so we also unmaks EINT when resume is done.
		 */
		mt_eint_mask(CUST_EINT_MT6280_USB_WAKEUP_NUM);
#endif

		retries = 10000;

#ifdef CONFIG_MTK_ICUSB_SUPPORT
		if (skip_port_pm_attr.value) {
			MYDBG("skip hw operation for port suspend\n");
		} else {
			power &= ~MUSBFSH_POWER_RESUME;
			power |= MUSBFSH_POWER_SUSPENDM;
			musbfsh_writeb(mbase, MUSBFSH_POWER, power);

			/* Needed for OPT A tests */
			power = musbfsh_readb(mbase, MUSBFSH_POWER);
			while (power & MUSBFSH_POWER_SUSPENDM) {
				power = musbfsh_readb(mbase, MUSBFSH_POWER);
				if (retries-- < 1)
					break;
			}
		}
#else
		power &= ~MUSBFSH_POWER_RESUME;
		power |= MUSBFSH_POWER_SUSPENDM;
		musbfsh_writeb(mbase, MUSBFSH_POWER, power);

		/* Needed for OPT A tests */
		power = musbfsh_readb(mbase, MUSBFSH_POWER);
		while (power & MUSBFSH_POWER_SUSPENDM) {
			power = musbfsh_readb(mbase, MUSBFSH_POWER);
			if (retries-- < 1) {
				MYDBG("\n");
				break;
			}
		}
#endif
		mb(); /* flush POWER and PHY setting immediately */
		WARNING("Root port suspended, power 0x%02x\n", power);

#ifdef CONFIG_MTK_DT_USB_SUPPORT
#if defined(CONFIG_PM_RUNTIME)
		disable_usb11_clk();
#endif
#endif
		musbfsh->port1_status |= USB_PORT_STAT_SUSPEND;
	} else {

#ifdef CONFIG_MTK_DT_USB_SUPPORT
		if (musbfsh_skip_port_resume) {
			MYDBG("\n");
			request_wakeup_md_timeout(0, 0);
			musbfsh->port1_status |= MUSBFSH_PORT_STAT_RESUME;
			musbfsh->rh_timer = jiffies + msecs_to_jiffies(20);
			return;
		}
#if defined(CONFIG_PM_RUNTIME)
		enable_usb11_clk();
#endif
#endif

		power = musbfsh_readb(mbase, MUSBFSH_POWER);
		if (!(power & MUSBFSH_POWER_SUSPENDM)) {
			WARNING("Root port resuming abort, power 0x%02x\n",
				power);
			if (power & MUSBFSH_POWER_RESUME)
				goto finish;
			else
				return;
		}
#ifdef CONFIG_MTK_DT_USB_SUPPORT
		request_wakeup_md_timeout(0, 0);
#endif

#ifdef MTK_USB_RUNTIME_SUPPORT
		/* ERR("EINT to wake up MD for resume\n"); */
		/* request_wakeup_md_timeout(0, 0); //wx, wakeup MD first */
#endif

#ifdef CONFIG_MTK_ICUSB_SUPPORT
		if (skip_port_pm_attr.value) {
			MYDBG("skip hw operation for port resume\n");
		} else {
			power &= ~MUSBFSH_POWER_SUSPENDM;
			power |= MUSBFSH_POWER_RESUME;
			musbfsh_writeb(mbase, MUSBFSH_POWER, power);
		}
#else
		power &= ~MUSBFSH_POWER_SUSPENDM;
		power |= MUSBFSH_POWER_RESUME;
		musbfsh_writeb(mbase, MUSBFSH_POWER, power);
#endif
		mb();  /* flush POWER and PHY setting immediately */
		WARNING("Root port resuming, power 0x%02x\n", power);
finish:
		/* later, GetPortStatus will stop RESUME signaling */
		musbfsh->port1_status |= MUSBFSH_PORT_STAT_RESUME;
		musbfsh->rh_timer = jiffies + msecs_to_jiffies(20);
	}
}

static void musbfsh_port_reset(struct musbfsh *musbfsh, bool do_reset)
{
	u8 power;
	void __iomem *mbase = musbfsh->mregs;

	/* NOTE:  caller guarantees it will turn off the reset when
	 * the appropriate amount of time has passed
	 */
	power = musbfsh_readb(mbase, MUSBFSH_POWER);
	WARNING("reset=%d power=0x%x\n", do_reset, power);
	if (do_reset) {
		if (power & MUSBFSH_POWER_SUSPENDM) {
			WARNING("reset a suspended device\n");
#ifdef CONFIG_MTK_DT_USB_SUPPORT
			request_wakeup_md_timeout(0, 0);
#endif

#ifdef MTK_USB_RUNTIME_SUPPORT
			/* ERR("EINT to wake up MD for reset\n"); */
			/* wx, we may have to reset a suspended MD */
			/* request_wakeup_md_timeout(0, 0); */
#endif
			musbfsh_writeb(mbase,
				       MUSBFSH_POWER, power |
				       MUSBFSH_POWER_RESUME);
			mdelay(20);
			musbfsh_writeb(mbase, MUSBFSH_POWER,
				       power & ~MUSBFSH_POWER_RESUME);
		}

		/*
		 * If RESUME is set, we must make sure it stays minimum 20 ms.
		 * Then we must clear RESUME and wait a bit to let musb start
		 * generating SOFs. If we don't do this, OPT HS A 6.8 tests
		 * fail with "Error! Did not receive an SOF before suspend
		 * detected".
		 */
		if (power & MUSBFSH_POWER_RESUME) {
			WARNING("reset a resuming device\n");
			while (time_before(jiffies, musbfsh->rh_timer))
				mdelay(1);
			/* stop the resume signal */
			musbfsh_writeb(mbase, MUSBFSH_POWER,
				       power & ~MUSBFSH_POWER_RESUME);
			mdelay(1);
		}

		musbfsh->ignore_disconnect = true;
		power &= 0xf0;
		musbfsh_writeb(mbase, MUSBFSH_POWER,
			       power | MUSBFSH_POWER_RESET);
		mb();  /* flush POWER and PHY setting immediately */
		musbfsh->port1_status |= USB_PORT_STAT_RESET;
		musbfsh->port1_status &= ~USB_PORT_STAT_ENABLE;
		musbfsh->rh_timer = jiffies + msecs_to_jiffies(50);
	} else {
		INFO("Root port reset stopped\n");

#ifdef CONFIG_MTK_ICUSB_SUPPORT

		if (resistor_control_attr.value) {
			/* improve signal quality, from Dingjun */

			/* original flow from SS5 */
			USB11PHY_SET8(U1PHTCR2,
				      force_usb11_dm_rpd | force_usb11_dp_rpd);

			/*
			 * disconnect host port's pull down resistors
			 * on D+ and D-
			 */
			USB11PHY_CLR8(U1PHTCR2,
				      RG_USB11_DM_RPD | RG_USB11_DP_RPD);

			/*
			 * Tell MAC there still is a device attached,
			 * ohterwise we will get disconnect interrupt
			 */
			USB11PHY_SET8(U1PHTCR2,
				      force_usb11_dp_rpu | RG_USB11_DP_RPU);

			/* force */
			USB11PHY_SET8(0x6a, 0x20 | 0x10);
			/* RG */
			/*
			 * disconnect host port's pull down resistors
			 * on D+ and D-
			 */
			USB11PHY_CLR8(0x68, 0x80 | 0x40);

			/*
			 * Tell MAC there still is a device attached,
			 * ohterwise we will get disconnect interrupt.
			 */
			/* USB11PHY_SET8(U1PHTCR2,
			 *		 force_usb11_dp_rpu |
			 *		 RG_USB11_DP_RPU);
			 */

			MYDBG("USB1.1 PHY special config for IC-USB\n");
		} else {
			MYDBG("");
		}
#endif
		musbfsh_writeb(mbase,
			       MUSBFSH_POWER, power & ~MUSBFSH_POWER_RESET);


#ifdef CONFIG_MTK_ICUSB_SUPPORT
		if (resistor_control_attr.value)
			USB11PHY_CLR8(0x6a, 0x20 | 0x10);
		else
			MYDBG("");
#endif
		mb(); /* flush POWER and PHY setting immediately */
		musbfsh->ignore_disconnect = false;

		power = musbfsh_readb(mbase, MUSBFSH_POWER);
		if (power & MUSBFSH_POWER_HSMODE) {
			INFO("high-speed device connected\n");
			musbfsh->port1_status |= USB_PORT_STAT_HIGH_SPEED;
		}
		musbfsh->port1_status &= ~USB_PORT_STAT_RESET;
		musbfsh->port1_status |=
			USB_PORT_STAT_ENABLE | (USB_PORT_STAT_C_RESET << 16) |
			(USB_PORT_STAT_C_ENABLE << 16);

		/* call back func to notify the hub thread the state of hub! */
		usb_hcd_poll_rh_status(musbfsh_to_hcd(musbfsh));

		musbfsh->vbuserr_retry = VBUSERR_RETRY_COUNT;
	}
}

void musbfsh_root_disconnect(struct musbfsh *musbfsh)
{
	INFO("%s++\r\n", __func__);
	musbfsh->port1_status =
		USB_PORT_STAT_POWER | (USB_PORT_STAT_C_CONNECTION << 16);

	usb_hcd_poll_rh_status(musbfsh_to_hcd(musbfsh));
	musbfsh->is_active = 0;
}


/*---------------------------------------------------------------------*/

/* Caller may or may not hold musbfsh->lock */
int musbfsh_hub_status_data(struct usb_hcd *hcd, char *buf)
{
	struct musbfsh *musbfsh = hcd_to_musbfsh(hcd);
	int retval = 0;

	INFO("called++\r\n");
	/* called in_irq() via usb_hcd_poll_rh_status() */
	if (musbfsh->port1_status & 0xffff0000) {
		*buf = 0x02;
		retval = 1;
	}
	return retval;
}

int musbfsh_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
			u16 wIndex, char *buf, u16 wLength)
{
	struct musbfsh *musbfsh = hcd_to_musbfsh(hcd);
	u32 temp;
	int retval = 0;
	unsigned long flags;

	INFO("%s++, typeReq=0x%x, wValue=0x%x, wIndex=0x%x\r\n",
	     __func__, typeReq, wValue, wIndex);
	spin_lock_irqsave(&musbfsh->lock, flags);

	if (unlikely(!HCD_HW_ACCESSIBLE(hcd))) {
		spin_unlock_irqrestore(&musbfsh->lock, flags);
		return -ESHUTDOWN;
	}

	/* hub features:  always zero, setting is a NOP
	 * port features: reported, sometimes updated when host is active
	 * no indicators
	 */
	switch (typeReq) {
	case ClearHubFeature:
	case SetHubFeature:
		switch (wValue) {
		case C_HUB_OVER_CURRENT:
		case C_HUB_LOCAL_POWER:
			break;
		default:
			goto error;
		}
		break;
	case ClearPortFeature:
		/* wIndex indicate the port number, here it is should be 1 */
		if ((wIndex & 0xff) != 1)
			goto error;

		switch (wValue) {
		case USB_PORT_FEAT_ENABLE:
			break;
		case USB_PORT_FEAT_SUSPEND:
			/* here is clearing the suspend */
			musbfsh_port_suspend(musbfsh, false);
			break;
		case USB_PORT_FEAT_POWER:
#ifndef MTK_ALPS_BOX_SUPPORT
			/* only power off the vbus */
			musbfsh_set_vbus(musbfsh, 0);
#else
			/* only power off the vbus */
			musbfsh_platform_set_vbus(musbfsh, 0);
#endif
			break;
		case USB_PORT_FEAT_C_CONNECTION:
		case USB_PORT_FEAT_C_ENABLE:
		case USB_PORT_FEAT_C_OVER_CURRENT:
		case USB_PORT_FEAT_C_RESET:
		case USB_PORT_FEAT_C_SUSPEND:
			break;
		default:
			goto error;
		}
		INFO("clear feature %d\n", wValue);
		musbfsh->port1_status &= ~(1 << wValue);
		break;
	case GetHubDescriptor:
		{
			struct usb_hub_descriptor *desc = (void *)buf;

			desc->bDescLength = 9;
			desc->bDescriptorType = 0x29;
			desc->bNbrPorts = 1;

			/* 0x0001: per-port power switching */
			/* 0x0010: no overcurrent reporting */
			desc->wHubCharacteristics =
				cpu_to_le16(0x0001 | 0x0010);
			/* msec/2 */
			desc->bPwrOn2PwrGood = 5;
			desc->bHubContrCurrent = 0;

			/* workaround bogus struct definition */
			desc->u.hs.DeviceRemovable[0] = 0x02;	/* port 1 */
			desc->u.hs.DeviceRemovable[1] = 0xff;
		}
		break;
	case GetHubStatus:
		temp = 0;
		*(__le32 *)buf = cpu_to_le32(temp);
		break;
	case GetPortStatus:
		if (wIndex != 1)
			goto error;

		/* finish RESET signaling? */
		/* if FALSE: stop the reset because the timeout of reset. */
		if ((musbfsh->port1_status & USB_PORT_STAT_RESET)
		    && time_after_eq(jiffies, musbfsh->rh_timer))
			musbfsh_port_reset(musbfsh, false);

		/* finish RESUME signaling? */
		if ((musbfsh->port1_status & MUSBFSH_PORT_STAT_RESUME)
		    && time_after_eq(jiffies, musbfsh->rh_timer)) {
			u8 pwr;
#ifdef CONFIG_MTK_DT_USB_SUPPORT
			if (!musbfsh_skip_port_resume) {
				pwr = musbfsh_readb(musbfsh->mregs,
						      MUSBFSH_POWER);
				pwr &= ~MUSBFSH_POWER_RESUME;
				WARNING("Root port resume stopped\n");
				WARNING("power 0x%02x\n", pwr);
				musbfsh_writeb(musbfsh->mregs, MUSBFSH_POWER,
					       pwr);
#if defined(CONFIG_PM_RUNTIME) && defined(USB11_REMOTE_IRQ_NON_AUTO_MASK)
				enable_remote_wake_up();
#endif
			} else {
				MYDBG("\n");
			}
#else

			pwr = musbfsh_readb(musbfsh->mregs, MUSBFSH_POWER);
			pwr &= ~MUSBFSH_POWER_RESUME;
			WARNING("Root port resume stopped, power 0x%02x\n",
				pwr);
			musbfsh_writeb(musbfsh->mregs, MUSBFSH_POWER, pwr);
#endif

#ifdef MTK_USB_RUNTIME_SUPPORT
			/* mt_eint_unmask(CUST_EINT_MT6280_USB_WAKEUP_NUM); */
#endif

			/*
			 * ISSUE: DaVinci (RTL 1.300) disconnects after
			 * resume of high speed peripherals (but not full
			 * speed ones).
			 */

			musbfsh->is_active = 1;
			musbfsh->port1_status &= ~(USB_PORT_STAT_SUSPEND
						   | MUSBFSH_PORT_STAT_RESUME);
			musbfsh->port1_status |= USB_PORT_STAT_C_SUSPEND << 16;
			usb_hcd_poll_rh_status(musbfsh_to_hcd(musbfsh));
		}

		put_unaligned(cpu_to_le32(musbfsh->port1_status &
					  ~MUSBFSH_PORT_STAT_RESUME),
					  (__le32 *)buf);

		/* port change status is more interesting */
		WARNING("port status %08x,devctl=0x%x\n", musbfsh->port1_status,
			musbfsh_readb(musbfsh->mregs, MUSBFSH_DEVCTL));
		break;
	case SetPortFeature:
		if ((wIndex & 0xff) != 1)
			goto error;

		switch (wValue) {
		case USB_PORT_FEAT_POWER:
			/* NOTE: this controller has a strange state machine
			 * that involves "requesting sessions" according to
			 * magic side effects from incompletely-described
			 * rules about startup...
			 *
			 * This call is what really starts the host mode; be
			 * very careful about side effects if you reorder any
			 * initialization logic, e.g. for OTG, or change any
			 * logic relating to VBUS power-up.
			 */
			INFO("musbfsh_start is called in hub control\r\n");
#ifdef CONFIG_MTK_ICUSB_SUPPORT
			if (skip_mac_init_attr.value)
				MYDBG("");
			else
				musbfsh_start(musbfsh);
#else
			musbfsh_start(musbfsh);
#endif
			break;
		case USB_PORT_FEAT_RESET:
			/* enable the reset, but not finish */
			musbfsh_port_reset(musbfsh, true);
			break;
		case USB_PORT_FEAT_SUSPEND:
			musbfsh_port_suspend(musbfsh, true);
			break;
		case USB_PORT_FEAT_TEST:
			break;
		default:
			goto error;
		}
		INFO("set feature %d\n", wValue);
		musbfsh->port1_status |= 1 << wValue;
		break;

	default:
error:
		/* "protocol stall" on error */
		retval = -EPIPE;
	}
	spin_unlock_irqrestore(&musbfsh->lock, flags);
	return retval;
}